E-mail: authentic013@steelpipes-fitting.com
WhatsApp: +86 13668807131
E-mail: authentic013@steelpipes-fitting.com
WhatsApp: +86 13668807131
Aug. 07, 2026
The raw material for seamless carbon steel elbows is seamless steel pipe. The main production process involves heating and piercing a round tube billet, then rolling it using three-roll cross rolling, continuous rolling, or extrusion to set (or reduce) the outer diameter of the pipe. After cooling, it is straightened. It undergoes direct hydrostatic testing (or flaw detection), is marked, and then stored. Schxx represents the wall thickness grade; 180e (S) indicates a short-radius 180° carbon steel elbow, and 180e (L) indicates a long-radius 180° elbow; 90E (S) indicates a short-radius 90° carbon steel elbow, and 90e (L) indicates a long-radius 90° elbow; 45E (L) indicates a long-radius 45° elbow, and 45E (S) indicates a short-radius 45° elbow.
The principle for determining the heating temperature of carbon steel elbows is: the austenitizing temperature of the material must be higher than this temperature, and the principal compressive stress on the inner wall of the elbow must be less than the yield strength of the material at this temperature. The higher the austenitizing temperature and heating temperature, the higher the yield strength and heating temperature, and the greater the advantages of seamless steel pipes.
Advantages of carbon steel seamless elbows: 1. Seamless elbow materials are entirely composed of carbon and hydrogen, and have passed the inspection of relevant national departments, ensuring hygiene. 2. Seamless elbows have good heat resistance and corrosion resistance; except for a small amount of hydrogenating agent, they will not rust or breed bacteria. 3. Seamless elbow materials have extremely low thermal conductivity, providing excellent thermal insulation performance compared to other insulation materials, which is well-known. 4. It should also be noted that stamped elbows have a very long service life, reportedly exceeding 50 years. Due to their rated temperature and pressure, they not only effectively resist radiation and ultraviolet rays, but the product also never fades.
Cangzhou Aosendike Pipe Fittings Manufacturing Co., Ltd. is a large-scale manufacturer specializing in elbows, tees, reducers, and pipe caps. We can comply with ASTM, ANSI, JIS, DIN, GB, and other standards, basically covering all steel materials.
If you have any purchasing needs or questions, please feel free to contact us.
Mobile: 86-13668807131
Website: https://www.authenticfitting.com/
Address: Mengcun Hui Autonomous County, Cangzhou City, Hebei Province
Email: authentic013@steelpipes-fitting.com
Previous: None
Latest News
Industry News
Aug. 07, 2026
Advantages of seamless carbon steel elbows
The raw material for seamless carbon steel elbows is seamless steel pipe. The main production process involves heating and piercing a round tube billet, then rolling it using three-roll cross rolling, continuous rolling, or extrusion to set (or reduce) the outer diameter of the pipe. After cooling, it is straightened. It undergoes direct hydrostatic testing (or flaw detection), is marked, and then stored. Schxx represents the wall thickness grade; 180e (S) indicates a short-radius 180° carbon steel elbow, and 180e (L) indicates a long-radius 180° elbow; 90E (S) indicates a short-radius 90° carbon steel elbow, and 90e (L) indicates a long-radius 90° elbow; 45
Industry News
Aug. 05, 2026
180° carbon steel pipe elbow manufacturing process
The most common manufacturing process for carbon steel pipe bends is hot forming. Hot forming is divided into two types: hot push bending and hot heating bending. Our 180° carbon steel pipe bends are manufactured using the hot push process. The process flow diagram is shown below.
Industry News
Aug. 03, 2026
What are the advantages of using sliding flanges?
A sliding flange is a type of slip-on flange. Slip-on welding involves welding only the outer layer, not the inner layer. Slip-on flanges are typically used for medium- and low-pressure pipelines with a nominal pressure less than 2.5 MPa. There are four types of sealing faces for slip-on flanges: flat face, raised face (RF), FM/M, and tongue and groove (TG). Flat face is the most widely used and the cheapest. A sliding flange is a slip-on flange with a short neck. Carbon steel sliding flanges, or SO flanges, are generally cheaper than welded neck flanges, which is why customers often choose sliding flanges. As the name suggests, a sliding flange fits over a
Authentic is here to help you find the right pipe fittings and flanges for your specific needs.
FAQ
What certifications do your products have?
Our products comply with international standards such as ASTM, ANSI, JIS, DIN, and GB. We also hold various certifications to assure quality and reliability, including ISO 9001.
How can I get some samples?
If you need, we will offer you samples for free, but new customers are expected to pay express charge.
To which country have you supplied your products?
We have supplied to Thailand, China Taiwan, Vietnam, India, South Africa, Sudan, Peru, USA, Brazil, Trinidad and Tobago, Kuwait, Qatar, Sri Lanka, Pakistan, Romania, France, Spain, Germany, Belgium, Ukraine etc. (Figures here only include our customers in latest 5 years.)
Get Quote
Have questions or need a custom solution? Reach out to us!
Our team at Authentic is here to help you find the right pipe fittings and flanges for your specific needs.
You Can Contact Us in the Following Ways
authentic013@steelpipes-fitting.com
+86 13668807131
Donghe Industrial Zone, Mengcun County, Cangzhou City, Hebei Province
Get Quote
At Authentic, we understand that every project has unique requirements. Our dedicated team is here to provide you with a customized quote tailored to your specific needs. By filling out the form below, you’ll receive competitive pricing, high-quality product details, and estimated delivery times.
中文
Русский
Español
عربي
